Linear Drivers – Casambi NFC 120-277 / CC150-1400 – 2 Channel

Description

The luminaire manufacturer is responsible for measuring and verifying the EMl compliance of the complete luminaire, as the level of radio interference will vary depending on the luminaire construction. Especially primary and secondary cable lengths and their routing may have a significant effect on radio interference.

165742
Output current	Input voltage	Output voltage	Efficiency @ full load	Current accuracy	Power factor	Dimension LxWxH (mm)
150 mA	120 Vac	10…54 Vdc	83%	± 5%	0.9 @ ＞10 W load	360 x 30 x 21
350 mA		10…54 Vdc	86%
750 mA		10…54 Vdc	89.5%
1000 mA		10…54 Vdc	89.5%
1200 mA		10…45 Vdc	88%
1400 mA		10…38.5 Vdc	88%
150 mA	277 Vac	10…54 Vdc	79.5%		0.9 @ ＞40 W load
350 mA		10…54 Vdc	83%
750 mA		10…54 Vdc	89.5%
1000 mA		10…54 Vdc	89.5%

Mains voltage supply
Rated input voltage range	120…277 Vac; performance range
Max. input voltage range	108…305 Vac; operational safety range
Rated frequency range	50/60 Hz
Performance / Operational safety	47…63 Hz
Max. input current	0.58 A @ 120 Vac
Withstand voltage	I/P-FG:1.8 kVac, < 5 mA 60 s; O/P-FG: 0.6 kVac, < 5 mA 60 s; I/P-O/P: 1.8 kVac, < 5 mA 60 s
Mains surge immunity	L-N 1 kV, L/N-FG: 2kV per IEC 61000-4-5
Ringing wave	L-N 2.5 kV, L-FG 2.5 kV, N-FG 2.5 kV
Total harmonic distortion (THD)
At rated input voltage range @ full load	≤ 10% @ 120 Vac; ≤ 15% @ 277 Vac
Output data
Output current tolerance	± 5% at rated input voltage range
No load output voltage	60 Vdc
Ripple output current	5% (ripple = peak/average total 100/120 Hz)
Output PstLM	≤ 1 at full load @ rated input voltage
Output SVM	≤ 0.4 at full load @ rated input voltage
Protection functions output side
Over voltage protection	The output voltage is less than or equal to 60 V Over voltage protection: Hiccup mode. protection device will trigger when load voltage exceeds specified output voltage and will auto recover after the fault mode is removed.
Overpower protection	The output power is less than or equal to 59.4 W
Short circuit protection	Short circuit protection: Hiccup mode. Protection device will trigger when short circuit and will auto recover after the fault mode is removed.
Dimming operation and interface
Dimming current range	1%…100%
Standby power consumption	< 0.5 W
Connection terminals
Connection terminal type	45° push in terminal
Wire cross section	lnput and output wire: 18-20 AWG
Wire stripping length	9…10 mm
Degree of protection
Protection rating	IP20
Operating data
Output current range	NFC control adjusts the current: 150…1400 mA
Default current	150 mA
Output voltage range	10…54 Vdc
Noise level	< 20 dB, at full load @ 100 cm distance

Operating temperature	-20…+50C
Storage temperature	-25…+85C
Working humidity	5%…90%
Store humidity	5%…95%
Lifetime	at Tc 90C: 50,000 hrs; at Tc 80C: 100,000 hrs @ 120 Vac 0.2% / 1,000 h failure rate
Maximum Tc temperature	90C

Housing dimensions		Packaging details
Length (L)	360 mm	Packing units	20 pcs
Width (W)	30 mm	Carton size	381 x 128 x128 mm
Height (H)	21 mm	Weight	6.4 kg
Weight	0.269 kg

All connections must be as short as possible to ensure good EMl performance.
The luminaire wire should keep a certain distance from the LED power supply and other wires (5…10 cm is preferred).
No secondary switches are allowed.
Incorrect wiring can damage the LED.
The wire must be well protected against short circuit.

NTC + / – interface voltage 3.3 V
Could connect to external NTC
NTC thermal management protects LED lamp , when the temperature of LED lamp over temperature protection point,
the current will be reduced by 50% every 5 minutes . Default setting is 85C .