Linear Drivers – DMX 120-347

Description

Product features

• DMX dimming isolated adjustable power LED driver
• 2Channel Intelligent DC to DC LED driver
• Flicker-free LED driver
• 12 V 0.1 A Auxiliary source
• Current adjustment via NFC
• NTC use for lamp temperature acquisition or output current set
• Output current 150…1400 mA
• Max. output power 54 W
• Constant lumen output (CLO)
• For luminaires with protection class I,II
• 5 years warranty

165773
Output current	Input voltage	Output voltage	Efficiency @ full load	Current accuracy	Power factor	Dimension LxWxH (mm)
150 mA	120 Vac	10…54 Vdc	83%	5%	0.9 @＞10 W load	360 x 30 x 21
350 mA		10…54 Vdc	86%
750 mA		10…54 Vdc	89.5%
1000 mA		10…54 Vdc	89.5%
1200 mA		10…45 Vdc	88%
1400 mA		10…38.5 Vdc	88%
150 mA	277 Vac	10…54 Vdc	79.5%		0.9 @＞40 W load
350 mA		10…54 Vdc	83%
750 mA		10…54 Vdc	89.5%
1000 mA		10…54 Vdc	89.5%
1200 mA		10…54 Vdc	89.5%
1400 mA		10…38.5 Vdc	88.5%

Mains voltage supply
Rated input voltage range				120…347 Vac; performance range
Max. input voltage range				108…380 Vac; operational safety range
Rated frequency range				50/60 Hz
Performance / Operational safety				47…63 Hz
Max. input current				0.58 A @ 120 Vac

Protection against voltage peaks
Withstand voltage				I/p-O/p: 1.8 kVac, < 5 mA 60 s; I/p-FG: 1.8 kVac, < 5 mA 60 s I/p-DIM: 1.8 kVac, < 5 mA 60 s; DIM-FG: 0.6 kVac, < 5 mA 60 s O/p-FG: 0.6 kVac, < 5 mA 60 s
Mains surge immunity				L-N 1 kV, L/N-FG: 2kV per IEC 61000-4-5
Ringing wave				L-N 2.5 kV, L-FG 2.5 kV, N-FG 2.5 kV

Total harmonic distortion (THD)
At rated input voltage range @ full load				≤ 10% @ 120 Vac; ≤ 20% @ 347 Vac

Output data
Output current tolerance				± 5% at rated input voltage range
No load output voltage				60 Vdc
Ripple output current				5% (ripple = peak/average tota 100/120 Hz)
Output PstLM				≤ 1 at full load @ rated input voltage
Output SVM				≤ 0.4 at full load @ rated input voltage

Protection functions output side
Over voltage protection				The output voltage is less than or equal to 60 V Over voltage protection: Hiccup mode. protection device will trigger when load voltage exceeds specified output voltage and will auto recover after the fault mode is removed.
Overpower protection				The output power is less than or equal to 59.4 W
Short circuit protection				Short circuit protection: Hiccup mode. Protection device will trigger when short circuit and will auto recover after the fault mode is removed.

Dimming operation and interface
Dimming mode				1%…100%
Standby power consumption				Amplitude dimming
Dimming current range				< 0.5 W

Connection terminals
Connection terminal type				45° push in terminal
Wire cross section				lnput and output wire: 18-20 AWG
Wire stripping length				9…10 mm

Degree of protection
Protection rating				IP20

Operating data
Output current range				NFC control adjusts the current: 150…1400 mA
Default current				150 mA
Output voltage range				10…54 Vdc
Noise level				< 20 dB, at full load @ 100 cm distance

The luminaire manufacturer is responsible for measuring and verifying the EMl compliance of the complete luminaire, as the level of radio interference will vary depending on the luminaire construction. Especially primary and secondary cable lengths and their routing may have a significant effect on radio interference.

Operating temperature				-20…+50C
Storage temperature				-25…+85C
Working humidity				5%…90%
Store humidity				5%…95%
Lifetime				at Tc 90C: 50,000 hrs; at Tc 80C: 100,000 hrs @ 120 Vac （0.2% / 1,000 h failure rate）
Maximum Tc temperature				90C

UL
/

CCC
/

SAA
/

Housing dimensions
Length (L)		360 mm
Width (W)		30 mm
Height (H)		21 mm
Weight		0.269 km

Packaging details
Packing units		20 pcs
Carton size		381 x 128 x128 mm
Weight		6.4 kg

All connections must be as short as possible to ensure good EMl performance.
The luminaire wire should keep a certain distance from the LED power supply and other wires (5…10 cm is preferred).
No secondary switches are allowed.
Incorrect wiring can damage the LED.
The wire must be well protected against short circuit.

NTC + / – interface voltage 3.3 V
Could connect to external NTC
NTC thermal management protects LED lamp , when the temperature of LED lamp over temperature protection point ,
the current will be reduced by 50% every 5 minutes . Default setting is 85C .
NTC compatibility list :